ref: dm85 inrush 090313jhm page 1 of 2 www.durakoolrelays.com sales department tel: (888) 847-6552 dm85 inrush pcb power relay contacts contact number & arrangement spst-no (1 n/o) contact material agsno 2 max. switching voltage ac/dc 440vac max. breaking capacity ac1 4000va min. switching current / voltage 10ma/10vdc max. inrush current 80a (20ms) rated load ac1 16a, 250vac (600 ops/hr) ac15 3a, 120v / 1.5a, 240v (b300) ac3 750w (single phase motor) dc1 16a, 24vdc dc13 0.22a, 120v / 0.1a, 250v (r300) initial resistance 100m?, max. at 0.1a/24vdc coil rated voltage dc 3...110v must release voltage dc 0.1un operating range of supply voltage see coil table 1 rated power consumption dc 0.4...0.48mw insulation (en 60664-1) insulation rated voltage ac 400vac rated surge voltage 4000v 1.2 / 50 s overvoltage category iii insulation pollution degree 3 dielectric strength coil to contact 5000vrms, 1min contact to contact 1000vrms, 1min contact - coil distance clearance 10mm creepage 10mm general data operating/release time (typical) ms 8ms/3ms electrical life ops >10 5 (16a 250vac) (ac1 / dc1 @ 600 ops/hr) mechanical life ops 3 x 10 7 (72000 ops/hr) dimensions l x w x h 29 x 12.7 x 15.7mm weight 14g ambient temperature storage -40 to 85c operating -40 to 85c shock resistance 30g vibration resistance 10g 10~150hz ? miniature pcb power relay ? up to 80a inrush (20ms) ? agsno 2 contacts ? rohs compliant specifcations are subject to change without notice. e&oe. e305753
dm85 inrush pcb power relay ref: dm85 inrush 090313jhm coil data (dc voltage 400 ...480mw) table 1 coil voltage code nominal voltage (vdc) coil resistance (?) 10% must release voltage min. (vdc) max. operating voltage (vdc) 1003 3 22 2.1 7.6 1005 5 60 3.5 12.7 1006 6 90 4.2 15.3 1009 9 200 6.3 22.9 1012 12 360 8.4 30.6 1018 18 710 12.6 45.9 1024 24 1440 16.8 61.2 1036 36 3140 25.2 91.8 1048 48 5700 33.6 122.4 1060 60 7500 42.0 153.0 1110 110 25200 77.0 280.0 note: parameters at 20c page 2 of 2 www.durakoolrelays.com sales department tel: (888) 847-6552 overall dimensions fig. 1 connection diagram fig. 2 (bottom view) dimensions in mm ordering codes type contact material contact arrangement cover protection and mounting coil code d m 8 5 - 5 0 2 1 - 2 5 - contact material see table 1 50 - agsno 2 contact arrangement 21 - spst-no (1 n/o) cover protection category 2 - in cover, fux tight - ip40 connection mode 5 - for pcb specifcations are subject to change without notice. e&oe. terminal (pin) dimensions terminal (pin) coil a1(1); a2 (2) contacts 21 (4);11(7); 4(8); 24(5) (mm) ? 0.6 0.5 x 0.9 drill hole: ? 1.3 +0.1mm (contact terminals should be tracked as shown above with 14 connected to 24, and 11 connected to 21 on the pcb)
|
